Altigen MAXCS 7.5 Softswitch Deployment Guide Uživatelský manuál Strana 16
- Strana / 37
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Page 16 of 37 MAXCS 7.5 All-Software Solution Deployment Guide
Note: Do not exceed the maximum numbers provided by the HMCP Certification Tool (from page 11).
The next section describes the parameters in this dialog box.
4. After adjusting these values, you may need to reboot the system so that the changes can take effect.
HMCP Resources Parameters
This panel shows the total number licensed (if applicable), total currently assigned, and the number assigned
to this HMCP board for Voice Processing Resources (VPR), station conference members, MeetMe conference
members, and agent supervision bridges.
The maximum number of resources that can be supported on an HMCP virtual board is as follows:
• G.711 VPR - 1,000
• G.711 / G.722 / G.723 / G.729 VPR - 200
• Station Conference Members - 120
• MeetMe Conference Members - 120
• Agent Supervision Bridges - 20
Notes
Important! When adding additional combo licenses, the system will increase the RTP ports it uses and
will use these new ports. If these additional ports are not added to the firewall, calls will not
have audio. Please refer to the MAXCS 7.5 ACM Administration Manual Appendix “Network
Ports” for instructions on how to identify these additional RTP ports.
• Codec G.722 is part of a combo codec and is controlled by license.
• 1,000 G.711 voice-processing resources will be licensed to the system when one HMCP Media Server
license is registered.
• Do not assign more codecs than the system can support. Doing so can degrade system performance.
• The more VPRs you assign, the slower the system will be when it starts up. To calculate the optimized
number of VPRs you need, use the following formula:
o Total G.711 VPRs = Total number of local IP extensions
o Total G.711/G.722/G.723/729 VPRs = Total number of remote IP phone users + Total Tie
Trunk Channels that will use compressed codec
Parameters in IP Header
This panel is where you configure QoS and TTL assignments.
• QoS assignment – IP TOS/DiffServ Byte Value. The default TOS/DiffServ byte hex value "A0"
(10100000) signals the network switch and router that RTP packets are "Critical". To set the value for
Diffserv Code Expedited Forwarding (DSCP EF), you can enter hex value "B8" (10111000).
• TTL assignment – For IP paging multicasting only. The purpose of the TTL (Time To Live) is to
regulate how many hosts the IP paging packets can pass through. The TTL value is reduced by one on
every hop. You may need to adjust this value if there are remote AltiGen IP phones at different
locations that register to MAXCS through WAN and require the IP paging feature. The value will be the
number of routers from MAXCS to remote IP phone plus one.
- MAXCS Release 7.5 1
- All-Software Solution 1
- Deployment Guide 1
- Contents 3
- Introduction 5
- Minimum Requirements 7
- Before You Begin 8
- Installation 8
- Step 3: Install MAXCS 11
- Step 4: Add the System Key 12
- Step 5: Register Licenses 14
- HMCP Resources Parameters 16
- Parameters in IP Header 16
- Step 15: Configure NAT 28
- Server 1 31
- Server 2 31
- Check Your Configuration 33
- Step 18: Out Call Routing 34
- AltiGen Technical Support 36
Související produkty a manuály pro Software Altigen MAXCS 7.5 Softswitch Deployment Guide
(7 stránky)Philips 75PFL5603/F7 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Soundbar-Lautsprecher Philips 75PFL5603/F7.
Wir stellen 1 PDF-Handbücher Philips 75PFL5603/F7 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Komentáře k této Příručce